Jumper NB168-JW2 is a high-speed jumper machine, and its production efficiency is several times to 100 times that of the small jumper machine in the market; It is suitable for large factories that require production efficiency. UPH: 30,000 points/hour is its biggest feature. Some of the functions have been replaced by the axial insertion machine, and this high-speed jumper is the best choice for the situation where there are many jumper insertion tasks.
Jumper machine NB168-JW2 exterior picture
Production video of jumper NB168-JW2
Technical parameters of jumper NB168-JW2
| item/项目 | Content | 内容 |
|---|---|---|
| Rated voltage:1-phase 220V | 额定电压:单相220V | |
| 电源Power Supply | Frequency:50/60Hz | 频率:50/60Hz |
| Rated capacity: Approx.2.0KVA | 额定功率:约2.0KVA | |
| 空气源Air supply | 供给气压:Min.0.5 Mpa-Max.0.8Mpa(运转气压0.45MPa~0.5MPa) | Supplied air pressure: Min.0.5 Mpa-Max.0.8Mpa (Operation air pressure0.45MPa~0.5MPa) |
| 供给空气量：约100L/min.(A.N.R) | Supplied air mass:Approx.100L/min.(A.N.R) | |
| 插入跨距 Insert span | 5-26mm(标准) 5-31mm(选配) | 5-26mm (standard) 5-31mm (optional) |
| 设备尺寸Dimensions | L:2055mm,W:1520mm,H:1600mm(不包信号塔料架) | L:2055mm,W:1520mm,H:1600mm(Not including signal towe) |
| 质 量 M a s s | 主机重量: 约1,300kg(仅主机) | Host weight: Approx.1,300kg(Main body only) |
| 环境条件 Environmental requirements | 温度:20℃±10℃ | Ambient temperature:20℃土10℃ |
| 通过LCD彩色触摸屏进行对话式的操作。 | Interactive operation via color LCD touch screen. | |
| 操作部 Operating controls | 输入和输出功能：U盘 插槽标准配置 | I/O functions：USB Slot standard equipment |
| 通信功能:LAN通信(TCP/IP) | Communication:LAN communication(TCP/IP) | |
| 外观颜色Color | 标准颜色:白色+蓝色 | Standard color:White+blue |
| 插入节拍(速度) Insertion tact time | UPH: 30000点/小时 最高速度节拍时间约 0.12秒/点(0.14、0.16、0.18s/点，可切换) | UPH: 30000 points/hour Max.tact time:Approx.0.12s/point (0.14,0.16,0.18s/point changeable) |
| 跳线传输部 Jumper transmission uni | 独立输送模式 | Independent conveying mode |
| 可同时插入2种不同规格的筒装跳线(选配) | Can be inserted atthe same time2 different specifications of barreljumper(optional) | |
| 基 板 更 换 时 间 PCB replacement time | 基板交换装载时间约3-4秒 | Approx.3~4 seconds |
| 基板尺寸:最小 50mm×50mm~最大 380mm×380mm | Dimensions:Min . 50mm×50mm~Max . 380mm×380mm | |
| 可插入范围：最小50mmx40mm~最大 370mm×370mm | Allowable insertion area:Min.50mmx40mm~Max.370mm×370mm | |
| 基板厚度: 1.6mm±0.15mm(标准可应对)最小0.6mm~最大2.36mm(选配) | Thickness:1.6mm±0.15mm(for tandard specification) Min.0.6mm~Max2.36mm(Special spectica) | |
| 适用基板 Applicable PCB | 基板重量:元件插入完毕的基板重量在1kg以内 | Mass:Max.1kg per board including inserted components. |
| 流向:右→左(标准)、左→右(选配) | Flow direction: right→left(Standard)、left→right(Option) | |
| 基板规正方法:销规正或者夹边定位 | Board positioning method:Pin positioning or Edge positioning | |
| 基板传输: 单板传输(标准) 双板传输(选配) | Board transfer: Single PCB transfer(Standard) Double PCB transfer(Special specification) | |
| 插入方向Insertion direction | 0°-360°方向(以1°递增) | 360° degrees by1° degree |
| 砧台Anvil | 弯脚角度 10°～35°剪脚长度1.2~2.2mm | Clinch Angle 10°～35°Cut Clinch Lungth1.2-2.2mm |
| 底座驱动：马达驱动 | Base Drive:Motor Drive | |
| 元件种类 No.of componentinputs | 可搭载40种类 | 40 inputs |
| 控制系统Control system | 微机方式 | Microcomputer system |
| X-Y轴:绝对坐标指令 | X-Y axes: Absolute coordinate commands | |
| 插入跨距:绝对指令 | Insertion pitch:Absolute commands | |
| 元件供给部:飞达号指令 | Component feeder:Feeder number designation | |
| X-Y工作台移动单位Least command increment of X-Y table | 0.01mm/脉冲 | 0.01mm/Pulse |
| 噪音水平 Noise Level | 约65 分贝 | Approx 65 db |
| 程序 Program | 主体内置式闪存器程序数量为2000+个 | Built-in flash memory 2000+prograrms |
| U盘根据卡的容量 | USB Disk Depending on USB disk memory | |
| 显示灯 Indication light | 信号塔(三色灯上起红、黄、绿) | Signal tower (3 lamps, op to bottom: red/yellow/green) |
| 孔位置补正方式 Hole position offset | 根据插入位置对所有孔识别结果(XY补正和Φ补正),算出最佳的插入位置，进行位置补正 | Determines optimum insertion positions based on the recognition of all insertion positions to make positional corrections (XY Correction and Φ Correction.). |
| 补插方式Recovery | 自动补插/手动机器补插(补插时间约为12秒) | Auto recovery/Auto recovery(Estimated Auto-recovery Time Approx.12s) |
| 自行诊断功能Self-diagnosis function | 当设备运行的状态下发生不良时，不良状况及故障信息显示在人机画面，并提示应对措施 | Presents on the color LCD the machine status when the power is ON and situation of any troubles occurred, as well as countermeasures against the troubles |
The above content is part of the jumper NB168-JW2, in the specific THT assembly and production process to choose the jumper machine, or the axial insertion machine is better, please consult online customer service to learn more